cal abbreviation; e.g., ea, in, pr, etc., and is the basis
erators SG-299/U, SG-
used to indicate quantities and allowances in subse-
299A/U, SG-299B/U ,
quent columns. When the unit of measure differs
and SG-299C/U.
from the unit of issue, the lowest unit of issue that
TM 11-6625-258-20P
Organizational Mainte-
will satisfy the required units of measure will be
nance Repair Parts and
requisitioned.
Special Tools Lists:
e. Quantity Incorporated in Unit. This column indi-
cates the quantity of the item used in the equipment.
299/U, SG-299A/U, SG-
Subsequent appearances of the same item in the
299B/U, and SG-
same assembly are indicated by the letters "REF".
299C/U.
f. 30-Day DS/GS Maintenance Allowances.
NOTE
1-5. Location of
Repair Parts
Allowances in GS column are for GS mainte-
a. This manual contains one cross-reference index
nance only.
(sec IV) to be
used to locate a
repair part when either
(1) The repair parts indicated by asterisk entries
t h e Federal stock number or reference number
i n separate allowance columns for GS represent
(Manufacturer's part number) is known. The first
those authorized for use at that category of mainte-
column in the index is prepared in numerical or al-
nance to be requisitioned on an "as required" basis,
phanumeric sequence in ascending order. The ref-
until stockage is based on demand in accordance with
erence numbers (manufacturer's part numbers) are
AR 710-2.
listed immediately following the last listed Federal
(2) Allowance quantities are indicated in the
stock number in the index of Federal stock numbers.
special tool lists section for special tools, TMDE, and
b. When the Federal stock number or reference
other support equipment.
number is known, follow the procedures given in (1)
g. 1-Year Allowances Per 100 Equipments/Con-
and (2) below.
tingency Planning Purposes. Column intentionally
(1) Refer to the index of Federal stock numbers
left blank.
(sec IV)
and locate the
Federal stock number or
ref-
h. Depot Maintenance Allowance Per 100 Equip-
erence number. The FSN and reference number are
ments. This column indicates opposite the first ap-
cross-referenced to the applicable figure and item
pearance of each item the total quantity authorized
number or reference designation.
for depot maintenance of 100 equipments.
(2) Refer to the repair parts list (sec II) and lo-
i. Illustration. This column is divided as follows:
cate the figure number (Col 10a) and item number or
(1) Figure number. Indicates the figure number
reference designation (C ol 10b) as noted in the FSN
of the illustration on which the item is shown in TM
index.
11-5134-15.
c. When the figure and item number or reference
(2) Item number. Indicates the item number or
designation are known, scrutinize columns 10a and
reference designation used to reference the item in
10b of the repair parts list (sec II) until the item is
the illustration.
located.
d. When the FSN, reference number, figure num-
ber, item number and reference designation are not
a. Usable on codes are included in column 3. Un-
known, scrutinize column 3 of the repair parts list
coded items are applicable to all models. Identifica-
(sec II), which is
arranged in
alphabetical order.
tion of the usable on codes used in this publication
.
are-
Code
Used On
Not applicable.
AF5
SG-299/U
1-7. Reporting of
Equipment Publication
AF6
SG-299A/U (Order No. 39108-PP-58)
AWW
SG-299A/U (Order No. 4502-PP-60)
Improvements
AF7
SG-299B/U
The reporting of errors, omissions, and recommenda-
AF8
SG-299C/U
tions for improving this publication by the individual
b. The following publication pertain to the equip-
user is encouraged. Reports should be submitted
ment and its components:
on DA Form 2028 (Recommended Changes to Pub-
lications) and forwarded direct to Commander, US
Organizational, DS, GS,
TM 11-5134-15
Army Electronics Command, ATTN: AMSEL-MA-
and Depot Maintenance
CRA, Fort Monmouth, N.J., 07703
Manual: Signal Gen-
(Nex printed page is 6.)